Parts & Accessories
B-RAD, which stands for Bottle Relocation and Accessory Device, is a system for organizing on-bike accessory storage using bottle cage mounts. Used alone to shift bottle cage location for clearance, or combine with other B-RAD accessories to carry tools, tubes pumps or a 2nd bottle on downtubes. - Single bottle mount with two slotted holes for adjustments up to 4mm +/- 10mm - Designed to maximize bottle capacity on small frame bikes and dual suspension frames
B-RAD, which stands for Bottle Relocation and Accessory Device, is a system for organizing on-bike accessory storage using bottle cage mounts. Used alone to shift bottle cage location for clearance, or combine with other B-RAD accessories to carry tools, tubes pumps or a 2nd bottle on downtubes. - Three slots for additional adjustments over the B-RAD 2 base - Compatible with triple bottle mounts on forks or frames, use neoprene pad and zip tie for use with standard bottle cage mounts
$24.95 - $34.95
The B-RAD Accessory Strap Mount is designed to add an additional strap point for tire levers, tubes or CO2 cartridges. Mounts to bottle bosses, or to the B-RAD base for additional carrying options. - Mounts to bottle bosses, or to the B-Rad base for additional carrying options - Main strap is 50mm wide and holds loads 75-120mm diameter (3 - 4.75 inches) - Cradle strap is 40mm wide and 350mm long for supporting loads
The USWE Phone Pocket is the perfect accessory for your USWE backpack. The Phone Pocket gives you the opportunity to access your phone quickly at any time without taking the pack off your back. The main compartment is meant for your phone and is accessed through the zipper on the side of the pocket. The secondary compartment is a mesh pocket on the front of the accessory. This compartment is perfect for stashing things like gels or keys for instant access. The pocket can fit a wide range of phones. The following measurements are approximately the maximum measurements a phone can have. - Standard: 14.5 cm (5.7") height x 6.5 cm (2.5") width - XL: 17.5 cm (6.9") height x 9.5 cm (3.8") width
Built from tough seatbelt webbing and a thick elastic strip, this cargo strap makes it easy to secure your gear. Use it a thousand different ways to make sure whatever you’re carrying stays with you all the way.
Mount a rack to any bike with this lightweight adapter that adds two M5 rear threaded eyelets to the seatpost. CONSTRUCTION • Aluminum
- Replacement stabilizers set for Bike Travel Bag Pro
The EVOC FRAME PAD protects the bike frame from scratches and other transport damage. - Fits most bike frames - Attachment for handlebar - Velcro straps attachment
B-RAD, which stands for Bottle Relocation and Accessory Device, is a system for organizing on-bike accessory storage using bottle cage mounts. Used alone to shift bottle cage location for clearance, or combine with other B-RAD accessories to carry tools, tubes pumps or a 2nd bottle on downtubes. - Long, four-slotted mount allows two, smaller bottles to be mounted in-line - Compatible with triple bottle mounts on forks or frames, use included neoprene pad and zip tie for use with standard bottle cage mounts
The B-RAD Dogbone allows for the bottle cage to mounted off center with additional B-RAD accessories, without needing the B-RAD base. Most commonly used for smaller, curved or dual suspension frames where the slotted bases won't fit or are not needed.
B-RAD Bottle Mounts allow for cargo customization and cargo optimization. They are designed to work in tandem with B-RAD Base mounts to keep cargo on the bike and off the back. - Compatible with any bike frame that has 2 standard 64mm spacing bottle cage mounts (most modern frames) - 6061-T6 aluminum brackets, stainless hardware - Weight (no hardware) – 20g - Maximum load 1700g - Designed to carry two bottles or accessories off of one B-RAD base
While the classic seat pack is a great place to store little-used essentials out of the elements, their mounting systems can interfere with and often damage modern dropper seatposts. Valais allows the use of a traditional seatbag on a dropper seatpost. - Allows the usage of seat packs on a dropper post - Protects the dropper stanchion from wear and grit - Can act as a travel limiter when full drop isn't needed - Sized by stanchion diameter
Replacement hardware, bolts and nuts for Wald baskets. Works with Wald Basket models: 520, 520GB, 535 and 535GB
The Gel Fuel Rack / NDM 1 give the user the ability to reach their gels and similar snacks at any time while our on the trails. The "grab-n-pull" aspect of the rack makes it super fast for you to fuel up with new energy. The accessory is compatible with backpacks equipped with the No Dancing Monkey 1.0 and No Dancing Monkey 1.2 harnesses. This attachment is compatible with the following products: - Raw - MTB Hydro - Airborne - Ranger - Patriot - Vertical - Outlander (NOT Compatible with Outlander PRO) With the Gel Fuel Rack / NDM 1 you'll always have instant access to your gels or other small snacks. The "grab-n-pull" make it super fast to fuel up with new energy. The accessory can be attached to the harness of all backpacks equipped with the No Dancing Monkey 1.0 and No Dancing Monkey 1.2 harnesses. The accessory is simply attached to the Velcro shoulder strap. This attachment is compatible with the following products:
Bolt-on eyelet for use with Tubus Lowrider racks and bags requiring bungee hook attachment.
This Tubus dropout extension adapter allows you to mount racks further back on the frame. It also allows you to mount traditional racks on bikes with disc brakes. - Weight: 66g - NOTE: This item is not compatible with any “EVO” Tubus racks
LM-1 Fork Adapter for rigid forks* with a diameter from 20mm up to 32mm. For all Tubus Lowriders except for Duo. *Please Note: Do NOT mount on suspension forks!
LM-BF 35 Fork Adapter, for forks without eyelets. Use with rigid forks* with a diameter from 25mm up to 40mm. For all Tubus lowriders except for Duo. *Please Note: Do NOT mount on suspension forks!
Mudgard Bracket for Rear Carriers
QR Axle Adapter with a set of adapter plates and mounting parts for assembling a rear carrier to frames without eyelets.
$7.00 - $9.00
Replacement stays for a variety of Tubus racks. Every roundstay is made out of solid aluminum, and they are available in various lengths and offsets. - 8mm diameter stay - Drilled for M5 bolts
Tubus strut clamp set for attaching and adjusting front stays on Cargo and Logo rear racks. - Aluminum block with stainless steel hardware - Fits 8mm diameter stays
Topeak's Cargo Net works with the Trolley Tote or MTX Rear Basket (sold separately). Make sure your goods stay in place on those bumpy rides home!
Solid aluminum dropper post mount to attach rear bikepacking bag, larger saddle bag, bottle cage, tail light, and more.
QuickClick mount for racing type saddles. Works with all Topeak Wedge Bags. - Material : Injected Nylon - Weight: 30g / 1.06 oz
Topeak's front basket handlebar fixer fits standard bikes or eBikes with display units. - Fits up to 1-inch handlebars
Fast and easy attachment of Topeak handlebar bags. - Clamp: Fits 25.4/28.6/31.8 mm Handlebars (shims included)
Take your bike adventures even further with a versatile mount cage to pack larger gear on your bike. The included tie-down straps provide the ability to carry a DryBag, sleeping bag/pad, stuff sack, or any round shaped gear on your bike frame or fork with bottle bosses. A four-hole mount design offers height adjustment of your load for better balance. VersaMount clamps also provide easy installation and flexible mounting options. - Fits tubes 20-60mm. - Engineering grade polymer - 64 mm mounting height adjustable - Weight: 128g - Max load: 3kg / 6.61lb - Dimensions: 22 x 12 x 7cm / 8.7 x 4.7 x 2.8-inches
Thule's Pack n' Pedal Side Frames mount quickly and easily to the sides of their Pack 'n Pedal Tour Rack (sold separately). They allow you to use any model of pannier for increased luggage capacity and a lower center of gravity.
Allows Thule Yepp Maxi to be installed on a bike with a rear rack with a load capacity of at least 35 kg/78 lbs and the ability to carry seat and bike bags. Features: - Fits rear racks measuring 11-17cm/4.5-6.7" - For use on rear racks with a load capacity of at least 35kg/78lbs
Page 1 of 4 Next page