Parts & Accessories
Crank Brothers' 5050 Pin Kit includes fifty 8mm-long steel pins that let you customize the traction on your 5050 or Mallet pedals. Thread lock is pre-applied to every pin.
Cleats with a more forgiving 10-deg release. - Optimized for novice riders or those new to clip-in pedals - 10-deg release angle makes it easier to unclip - 2-hole bolt pattern for mountain bike shoes - Plastic spacing shims included - Compatible with all Crankbrothers clip-in pedals
Widen your Q-factor to 57mm. - Long spindles are 5mm longer than standard. - The kit includes: 1 pair long spindles + refresh kit (Enduro cartridge bearings, igus ll-glide bearings, DSS double seal system: internal and external seals, hex alloy end caps, o-rings, nuts, sleeve bushings, & bearing removal tool). - Compatible with: Eggbeater, Candy, Mallet, 5050, Double shot, model years 2010-present - Weight: 112g per pair - Spindle material: forged SCM 435 chromoly steel - Q-factor: 57mm
$15.99 - $19.99
Everything you need to keep those Crank Bros pedals spinning freely is found in their Pedal Rebuild Kit. Each kit includes parts and instruction to rebuild one pair of Crank Bros. pedals.
Your pedals like to be pampered. The Crank Brothers Pedal Refresh Kit gives you everything you need to keep them happy. Pedal Refresh Kit includes: -Enduro catridge bearings - Igus LL-glide bearings - Double seal system (internal and external seals) - Hex alloy end caps - O-rings - Nuts - Sleeve bushings - Bearing removal tool Compatible with the following pedals (2010-present): - Eggbeaters - Candys - Mallets - 5050s
Crank Brothers' Premium MTB Cleats are perfect for your Crank Brothers Eggbeater, Candy, Acid, Smarty, Mallet, and Quattro pedals. They're made from solid brass for crisp entry and exit, and top-notch durability. - SPD compatibility - Weight (pair): 30g - Float: 6 degrees - Release angle: 15 or 20 degrees
Polyurethane pads with diamond plate traction pattern allow riders to customize their pedals for a perfect interface with any shoe. - Kit includes eight 1mm traction pads and eight 2mm traction pads
Pre-cut traction tabs designed to integrate with the Highline remote lever and increase grip for ultimate control.
A revolution in performance and reliability. - The kit includes premium internal components: - Inner spindle seal x 2 - Outer spindle seal x 2 - Inner Igus solid bearing x 2 - Outer Enduro cartridge bearing x 2 - Spindle nut x 2 - Outer bearing carrier x 2 - Compatibility: Doubleshot (2016), Doubleshot 2 (2017+), Soubleshot 3 (2017+)
A revolution in performance and reliability. The kit includes premium internal components: - Enduro catridge bearings - Enduro sealed needle bearing - Double seal system (internal and external seals) - Hex alloy end caps - O-rings, nuts - Sleeve bushings - Bearing removal tool
A revolution in performance and reliability. The kit includes premium internal components: - Inner bearing o-ring x 2 - Spindle seal x 2 - Outer Igus solid bearing x 2 - Inner Igus solid bearing half x 4 - Bearing Retainer Bolt x 4 - Outer o-ring x 2 - Grease port screw x 2 - Compatibility: Stamp (2016), Stamp 7 (2017+), Stamp 11 (2017+)
Kit Includes premium components: - Inner cartridge bearing x 2 - Outer cartridge bearing x 2 - Igus solid bearing x 2 - Inner seal x 2 - Bearing locknut x 2 - Spindle screw (Left) x 1 - Spindle screw (Right) x 1
Protect the soles of your shoes with the Shoe Shields from Crank Brothers. These stainless-steel plates install under your cleats and prevent the pedal from digging in to your carbon-soled shoes. - Sold in pairs
Customize and optimize the shoe/pedal interface. - Refine the interface between the shoe tread and pedal body - Four (4) contact sleeves - 1mm thickness
Engineered to optimize the interface between the pedal and shoe for ultimate performance and power transfer. The kit includes: - 8 × 1mm traction pads - 8 × 2mm traction pads Compatible with: - Candy 7 & 11 - Model years 2016 – present
Engineered to optimize the interface between the pedal and shoe for ultimate performance and power transfer. The kit includes: - 8 × 1mm traction pads - 8 × 2mm traction pads Compatible with: - Mallet E - Model years 2016 – present
Crank Brothers' Zero Float Cleats offer no pedal float for greater pedaling efficiency. They're made from solid brass for crisp entry and exit, and top-notch durability. - Weight (pair): 30 grams - Shoe compatibility: SPD - Release angle: 15 degrees
Page 1 of 1